Our own technology · FLT20

Solar steam for your process, with Fresnel optics

The FLT20 is a concentrating solar collector of our own patented design that uses Fresnel optics to heat a fluid up to 400 °C.

80–400 °Coperating temperature
30 barmaximum pressure
41.7 kWtper FLT tandem
25 kg/m²light enough for rooftops
01 · HOW IT WORKS

Mirrors that track the sun

Rows of extra-clear glass mirrors turn through the day, each on its own individually tracked axis, and reflect direct sunlight onto a receiver tube above them.

A CPC-type secondary reflector also captures the light that misses the tube and shields it from dirt, hail and birds. The absorber, a stainless-steel tube with a selective coating inside an evacuated glass envelope, turns that light into heat and transfers it to the fluid: steam, water or thermal oil.

When it is not operating, each axis turns the mirrors face-down, protected by an aluminium rear cover. A rain gauge with a hail sensor stows them before hail starts.

  • Second-surface low-iron glass mirrors with 94–95% reflectivity
  • Individual tracking per axis, with an error below 0.05°
  • CPC secondary reflector that protects the tube
  • Evacuated absorber with selective coating and anti-reflective glass
01
Fresnel mirrors face-up, in operation
Face-up · in operation
Fresnel mirrors face-down, at rest
Face-down · at rest
02 · MODULES

It arrives assembled. It connects in minutes.

Each FLT tandem is fully built and calibrated in our factory to guarantee its optical quality. It travels folded on a standard flatbed truck and is unfolded on site. At the plant, modules join with plug-and-play connections and are combined until they reach the power your process needs.

Its low weight means it can go on the ground or on the factory roof, and if your needs change, the modules can be relocated.

  • Built and calibrated in the factory
  • Plug-and-play connections between modules
  • On the ground or on the roof
  • Relocatable if your plant changes
On-site assembly
Pre-assembled Fresnel modules on a truck
Leaves the factory assembledTravels by truck, ready to install.
Fits in a containerFor projects outside Spain.
Slides into place on railsOn the roof, with no cranes on top.
Fresnel modules resting on the ground without foundations
No foundation worksRests on 8 feet; in large fields, on small concrete pads.
03 · Certifications

Tested by independent laboratories

Performance to ISO 9806 at the Plataforma Solar de Almería, optical characterisation of the mirrors and a full-size wind-tunnel test.

FL8 modules under test at the Plataforma Solar de AlmeríaFL5 modules under test at the Plataforma Solar de Almería
Plataforma Solar de Almería

ISO 9806

Performance certification

Module version
FL8 v.2
Test period
May 2025 – May 2026
Lab
Plataforma Solar de Almería (CIEMAT)
Module version
FL5 v.1
Test period
July 2021 – July 2022
Lab
Plataforma Solar de Almería (CIEMAT)
OPAC lab optical measurement device
Plataforma Solar de Almería

Optical characterisation

Primary reflectors

Date
July 2020
Lab
OPAC (DLR – PSA CIEMAT)
Full-size module section in the wind tunnel
CMT – Universitat Politècnica de València

Wind tunnel

Full-scale test campaign

Date
July 2023
Lab
CMT (UPV)
04 · DATASHEET

FLT20 linear Fresnel collector

Data per FLT tandem at reference conditions. Detailed optical performance is available on request.

3D model of an FLT tandem
FLT tandem in 3D.
Thermal power41.7 kWtper tandem · 52.1 kW gas equivalent
Net aperture79.2 m²
Land use112 m²between 93 and 130.6 m² depending on layout
Tandem dimensions16.3 m × 5.7 m
Specific weight25 kg/m²
Operating temperature80 °C to 400 °C
Maximum pressure30 bar
FluidsSteam, water and thermal oil
Optical efficiency η₀0.645ISO 9806:2017 · PSA test 2025–2026
Heat-loss coefficients c₁ / c₂0 / 1.44·10⁻⁴ W/(m²·K²)valid up to ΔT = 246 °C
Mirror reflectivity0.95
Maximum wind in operation / stowed50 km/h / 167 km/hextrapolated from full-size wind-tunnel tests
Service life20 years

Reference conditions: DNI 900 W/m², inlet 150 °C, outlet 180 °C, ambient 30 °C.

05 · OPERATION

It runs automatically. We supervise it remotely.

The plant runs on its own, with no dedicated operator: Heineken Valencia has operated without on-site supervision since 2023. From our offices we monitor every axis with tools we developed ourselves.

  • SUNPI. Status, position and history of every axis, with remote recalibration and firmware updates, also from a phone.
  • Maintenance app. Scanning a component’s QR code shows its manufacturing date, quality report, optical measurements, stock and manuals.
  • Digital twin. Compares production with the model in real time and generates reports automatically.
  • Automatic cleaning. A rain-cleaning protocol and an automatic cleaning robot tested at Heineken Valencia.
SUNPI · real-time tracking of every axis